0,0 → 1,159 |
# |
# vcs:conf: $Rev$ |
# Example vcs.conf file |
# This example files contains all the default values, commented out. |
# For each setting, where an equivalent command-line option exists it will be |
# listed in the comments |
# |
# Location: |
# Configuration files can be placed at /etc/vcs.conf (site-wide), |
# ~/.vcs.conf (current user, hidden file!), ./vcs.conf (current dir) or |
# ~/.vcs/vcs.conf (current user, new alternative location) |
# |
# Syntax: |
# * Comments start with '#' or ';' |
# * '#' can be used in values by writing $# |
# * Semicolons (;) can't be used in values |
# * Options are of the form name=value |
# - Options can refer to the *current* value of other options, i.e. |
# font_sign=$font_heading will assign to 'font_sign' the same value |
# as 'font_heading'. If font_heading is changed after that, font_sign |
# won't be affected. |
# - See <http://p.outlyer.net/dox/vcs:conf_files> for the full list |
|
# Height of individual captures. Percentage or fixed size (in pixels) |
#height=100% # option -H |
|
# Amount ignored from the end of the video (think of it as an anti-spoiler |
# measure). Percentage (of video duration) or time (e.g. 2m). Set to 0 |
# to disable it. |
#end_offset=5% # option -E |
|
######################## |
# Contact Sheet Layout # |
######################## |
|
#columns=2 # Number of columns in the contact sheet (option -c) |
|
#interval=1m # Interval between captures (option -i) |
|
# Number of captures. Note setting this isn't enough to use a fixed number, the |
# mode must also be changed (option 'timecode_from', see below). (option -n) |
#captures=16 |
|
# Mode of operation, can be either $TC_NUMCAPS or $TC_INTERVAL (the default) |
# $TC_NUMCAPS Fix the number of captures, adjust interval accordingly |
# $TC_INTERVAL Fix interval, adjust the number of captures accordingly |
# (options -i and -n set this implicitly) |
#timecode_from=$TC_INTERVAL |
|
# Modifier for extended mode (option -e). |
# Beware, setting it to something different from 0 automatically enables extended mode! |
#extended_factor=0 |
|
# Extra padding added around each capture. |
# This has *no effect* when shadows are enabled (the default). |
# Tweaking this might break alignment when using extended mode (-e) |
#padding=2 |
|
# Anonymous mode, set to 1 to disable the "Preview created by {value of user}" |
# line in the footer. (option --anonymous) |
#anonymous=0 |
|
# Profiles to load by default. (option -p) |
# *MUST* exist. |
#profiles= |
|
############### |
# Output file # |
############### |
|
# Output format. Use the file extension (e.g. 'png', 'jpg', 'jp2') |
# Any format accepted by ImageMagick can be used here (even pdf or gif, not |
# that they'll look very good though) |
# (options: -j for JPEG, -j2 for JPEG 2000) |
#format=png |
|
#quality=92 # Output quality for lossy formats (e.g. jpg) |
|
#################### |
# Cosmetic touches # |
#################### |
|
#user=`id -un` # User name, will be used in the contact sheet footer (option -u) |
|
# Used in the signature, e.g. "Preview created by {value of user}" |
#signature=Preview created by |
|
#disable_shadows=0 # Disable shadows by default (option -ds) |
|
#disable_timestamps=0 # Disable timestamps by default (option -dt) |
|
##################### |
# Colours and fonts # |
##################### |
|
# * Colours can be defined either by their name or through hexcodes |
# use the command 'identify -list color' for a list of known names |
# * Colours can use transparency, although this usually only makes sense |
# for timestamps, which are overlaid on captures. |
# * Beware when specifying colours in hex format color=#hex is ok |
# but color = #hex not, spaces can be used with color = $#hex |
# * Font sizes are expressed in points and hence might need adjustment |
# when the font is changed. |
# * Font names can be either font paths (e.g. /usr/something/ttf/font.ttf) |
# or font names as understood by ImageMagick, use the command |
# 'identify -list font' for a list of fonts known to ImageMagick |
|
#bg_heading=#afcd7a # Heading/meta-information section background colour |
#fg_heading=Black # Heading font colour |
#font_heading=DejaVu-Sans-Book # Heading font |
#pts_heading=14 # Font size for heading |
|
#bg_title=White # Background for the title (if activated with option -T) |
#fg_title=Black # Title font colour |
#font_title=$font_heading # Title font |
|
#bg_contact=White # Background for the contact sheet |
|
#bg_tstamps=#000000aa # Background for timestamps. Note the use of transparency |
#fg_tstamps=White # Timestamps font colour |
#font_tstamps=$font_heading # Timestamps font |
#pts_tstamps=14 # Font size for timestamps |
|
# Background for the signature, i.e. the section after the contact sheet with |
# vcs and user identification |
#bg_sign=SlateGray |
#fg_sign=Black # Font colour for the signature |
#font_sign=$font_heading # Font for the signature |
#pts_sign=10 # Font size for signature |
|
# Font to use for file name when the non-latin mode (--nonlatin) is enabled |
# Option: -Ik=fontname |
#nonlatin_font= # Autodetected (hopefully) |
|
###################### |
# Lower level tweaks # |
###################### |
|
# Decoder to use by default, can be either $DEC_FFMPEG (default) or |
# $DEC_MPLAYER |
# (options: -M for MPlayer, -F for FFMpeg) |
#decoder=$DEC_FFMPEG |
|
# Output from commands, useful to locate errors |
#stdout=/dev/null |
#stderr=/dev/null |
|
# Verbosity level, very verbose by default. |
# Possible values: $V_ALL (default), $V_ERROR, $V_WARN, $V_INFO, $V_NONE |
# (options: -q for quietness) |
#verbosity=$V_ALL |
|
# 1 disables colours in console output |
#simple_feedback=0 |
|
#debug=0 # When 1, enables debugging mode (option -D) |
|
#getopt=getopt # GNU Getopt executable name |
|
Property changes: |
Added: svn:keywords |
+Rev Id Date |
\ No newline at end of property |